CISCO 9124光纤交换机调试经历

思考的牛

CISCO 的交换机和普通的博科或者QLOGIC的交换机差别很大。普通的交换机直接进入默认IP地址，通过图形化界面直接配置就OK了。CISCO的交换机没有图形界面，因此解决需要如下配置步骤：

1、察看每个端口状态：

switch2# show interface fc1/1

fc1/1 is up

   Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)

   Port WWN is 20:01:00:0d:ec:be:0d:40

   Admin port mode is auto, trunk mode is on

   snmp link state traps are enabled

   Port mode is F, FCID is 0xd40300

   Port vsan is 1

   Speed is 4 Gbps

   Rate mode is dedicated

   Transmit B2B Credit is 8

   Receive B2B Credit is 16

   Receive data field Size is 2112

   Beacon is turned off

   5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

   5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

     378 frames input, 17228 bytes

       0 discards, 0 errors

       0 CRC, 0 unknown class

       0 too long, 0 too short

     56 frames output, 3536 bytes

       0 discards, 0 errors

     3 input OLS, 3 LRR, 0 NOS, 13 loop inits



switch2# show interface fc1/2

fc1/2 is up

   Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)

   Port WWN is 20:02:00:0d:ec:be:0d:40

   Admin port mode is auto, trunk mode is on

   snmp link state traps are enabled

   Port mode is F, FCID is 0xd40500

   Port vsan is 1

   Speed is 4 Gbps

   Rate mode is dedicated

   Transmit B2B Credit is 3

   Receive B2B Credit is 16

   Receive data field Size is 2112

   Beacon is turned off

   5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

   5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

     11839 frames input, 476672 bytes

       0 discards, 0 errors

       0 CRC, 0 unknown class

       0 too long, 0 too short

     161 frames output, 8952 bytes

       0 discards, 0 errors

     1 input OLS, 1 LRR, 0 NOS, 33 loop inits



switch2# show interface fc1/3

fc1/3 is down (Link failure: Link Reset)

   Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)

   Port WWN is 20:03:00:0d:ec:be:0d:40

   Admin port mode is auto, trunk mode is on

   snmp link state traps are enabled

   Port vsan is 1

   Receive data field Size is 2112

   Beacon is turned off

   5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

   5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

     966 frames input, 39704 bytes

       0 discards, 0 errors

       0 CRC, 0 unknown class

       0 too long, 0 too short

     89 frames output, 4424 bytes

       0 discards, 0 errors

     1 input OLS, 1 LRR, 0 NOS, 32 loop inits

     3 output OLS, 1 LRR, 5 NOS, 3 loop inits

Interface last changed at Sat Aug 8 19:16:01 2009



switch2# show interface fc1/7

fc1/7 is up

   Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)

   Port WWN is 20:07:00:0d:ec:be:0d:40

   Admin port mode is auto, trunk mode is on

   snmp link state traps are enabled

   Port mode is F, FCID is 0xd40000

   Port vsan is 1

   Speed is 4 Gbps

   Rate mode is dedicated

   Transmit B2B Credit is 8

   Receive B2B Credit is 16

   Receive data field Size is 2112

   Beacon is turned off

   5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

   5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

     296 frames input, 13284 bytes

       0 discards, 0 errors

       0 CRC, 0 unknown class

       0 too long, 0 too short

     301 frames output, 12820 bytes

       0 discards, 0 errors

     3 input OLS, 2 LRR, 1 NOS, 155 loop inits



switch2# show interface fc1/8

fc1/8 is up

   Hardware is Fibre Channel, SFP is short wave laser w/o OFC (SN)

   Port WWN is 20:08:00:0d:ec:be:0d:40

   Admin port mode is auto, trunk mode is on

   snmp link state traps are enabled

   Port mode is F, FCID is 0xd40200

   Port vsan is 1

   Speed is 2 Gbps

   Rate mode is dedicated

   Transmit B2B Credit is 3

   Receive B2B Credit is 16

   Receive data field Size is 2112

   Beacon is turned off

   5 minutes input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

   5 minutes output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec

     1265 frames input, 54276 bytes

       0 discards, 0 errors

       0 CRC, 0 unknown class

       0 too long, 0 too short

     309 frames output, 15104 bytes

       0 discards, 0 errors

     6 input OLS, 4 LRR, 0 NOS, 92 loop inits



1、配置VSAN

VSAN的作用是隔离每一个交换机端口：

switch2# conf t

Enter configuration commands, one per line. End with CNTL/Z.

switch2(config)# vsan database

switch2(config-vsan-db)# vsan 4000 name sw2

switch2(config-vsan-db)# vsan 4000 interface fc1/1

Traffic on fc1/1 may be impacted. Do you want to continue? (y/n) y

switch2(config-vsan-db)# vsan 4000 interface fc1/2

Traffic on fc1/2 may be impacted. Do you want to continue? (y/n) y

switch2(config-vsan-db)# vsan 4000 interface fc1/7

Traffic on fc1/7 may be impacted. Do you want to continue? (y/n) y

switch2(config-vsan-db)# vsan 4000 interface fc1/8

Traffic on fc1/8 may be impacted. Do you want to continue? (y/n) y

switch2(config-vsan-db)# end

switch2# show vsan 4000 membership

vsan 4000 interfaces:

fc1/1            fc1/2            fc1/7            fc1/8



2、创建ZONE并且添加ZONE成员。

witch2# conf t

Enter configuration commands, one per line. End with CNTL/Z.

switch2(config)# zone name db2_3652_1 vsan 4000

switch2(config-zone)# member interface fc1/1

switch2(config-zone)# member interface fc1/2

switch2(config-zone)# zoneset name db2_3652 vsan 4000

switch2(config-zone)# member interface fc1/7

switch2(config-zone)# member interface fc1/8



4、配置ZONESET包含2个ZONE

switch2(config-zone)# zoneset name db2_3652 vsan 4000

switch2(config-zoneset)# member db2_3652_1

switch2(config-zoneset)# member db2_3652_2



5、察看ZONE成员

switch2# show zone

zone name db2_3652_1 vsan 4000

interface fc1/1 swwn 20:00:00:0d:ec:be:0d:40

interface fc1/2 swwn 20:00:00:0d:ec:be:0d:40



zone name db2_3652_2 vsan 4000

interface fc1/7 swwn 20:00:00:0d:ec:be:0d:40

interface fc1/8 swwn 20:00:00:0d:ec:be:0d:40



6、察看ZONESET成员

switch2# show zoneset

zoneset name db2_3652 vsan 4000

zone name db2_3652_1 vsan 4000

   interface fc1/1 swwn 20:00:00:0d:ec:be:0d:40

   interface fc1/2 swwn 20:00:00:0d:ec:be:0d:40



zone name db2_3652_2 vsan 4000

   interface fc1/7 swwn 20:00:00:0d:ec:be:0d:40

interface fc1/8 swwn 20:00:00:0d:ec:be:0d:40



7、激活ZONESET    

switch2# conf t

Enter configuration commands, one per line. End with CNTL/Z.

switch2(config)# zoneset activate name db2_3652 vsan 4000

Zoneset activation initiated. check zone status



8、察看激活ZONE的

switch2# show zone active

zone name db2_3652_1 vsan 4000

* fcid 0x810000 [interface fc1/1 swwn 20:00:00:0d:ec:be:0d:40]

* fcid 0x810100 [interface fc1/2 swwn 20:00:00:0d:ec:be:0d:40]



zone name db2_3652_2 vsan 4000

* fcid 0x810200 [interface fc1/7 swwn 20:00:00:0d:ec:be:0d:40]

* fcid 0x810300 [interface fc1/8 swwn 20:00:00:0d:ec:be:0d:40]



第一个节点配置：

switch1# show vsan 4000 membership

vsan 4000 interfaces:

   fc1/1            fc1/2            fc1/3            fc1/7            

   fc1/8            



switch1# show zone

zone name db2_3651_1 vsan 4000

interface fc1/1 swwn 20:00:00:0d:ec:be:05:00

interface fc1/2 swwn 20:00:00:0d:ec:be:05:00


zone name db2_3651_2 vsan 4000

interface fc1/7 swwn 20:00:00:0d:ec:be:05:00

interface fc1/8 swwn 20:00:00:0d:ec:be:05:00

switch1# show zoneset

zoneset name db2_3651 vsan 4000

zone name db2_3651_1 vsan 4000

   interface fc1/1 swwn 20:00:00:0d:ec:be:05:00

   interface fc1/2 swwn 20:00:00:0d:ec:be:05:00


zone name db2_3651_2 vsan 4000

   interface fc1/7 swwn 20:00:00:0d:ec:be:05:00

   interface fc1/8 swwn 20:00:00:0d:ec:be:05:00

switch1# show zone active

zone name db2_3651_1 vsan 4000

* fcid 0xac0000 [interface fc1/1 swwn 20:00:00:0d:ec:be:05:00]

* fcid 0xac0100 [interface fc1/2 swwn 20:00:00:0d:ec:be:05:00]



zone name db2_3651_2 vsan 4000

* fcid 0xac0200 [interface fc1/7 swwn 20:00:00:0d:ec:be:05:00]

* fcid 0xac0300 [interface fc1/8 swwn 20:00:00:0d:ec:be:05:00]



9、最后别忘了保存！

switch1# copy running-config startup-config

[########################################] 100%

switch1#