配置Super VLAN 示例

胡振宇

<HUAWEI> system-view
[HUAWEI] sysname SwitchA
[SwitchA] vlan batch 2 to 3
[SwitchA] interface gigabitethernet 1/0/1
[SwitchA-GigabitEthernet1/0/1] port link-type access //和接入设备相连的接口类型设置为access
[SwitchA-GigabitEthernet1/0/1] port default vlan 2 //接口加入VLAN 2
[SwitchA-GigabitEthernet1/0/1] quit
[SwitchA] interface gigabitethernet 1/0/2
[SwitchA-GigabitEthernet1/0/2] port link-type access
[SwitchA-GigabitEthernet1/0/2] port default vlan 2
[SwitchA-GigabitEthernet1/0/2] quit
[SwitchA] interface gigabitethernet 1/0/3
[SwitchA-GigabitEthernet1/0/3] port link-type access
S7700&S9700 系列交换机
典型配置举例3 基础特性典型配置
文档版本 04 (2015-10-23) 华为专有和保密信息
版权所有 &copy; 华为技术有限公司
215
[SwitchA-GigabitEthernet1/0/3] port default vlan 3 //接口加入VLAN 3
[SwitchA-GigabitEthernet1/0/3] quit
[SwitchA] interface gigabitethernet 1/0/4
[SwitchA-GigabitEthernet1/0/4] port link-type access
[SwitchA-GigabitEthernet1/0/4] port default vlan 3
[SwitchA-GigabitEthernet1/0/4] quit
# 配置接口GE1/0/5透传VLAN 2和VLAN 3。
[SwitchA] interface gigabitethernet 1/0/5
[SwitchA-GigabitEthernet1/0/5] port link-type trunk
[SwitchA-GigabitEthernet1/0/5] port trunk allow-pass vlan 2 to 3
[SwitchA-GigabitEthernet1/0/5] quit
步骤2 配置SwitchB
# 创建VLAN 2、VLAN 3、VLAN 4、VLAN 10，并配置SwitchB连接SwitchA的接口，
使VLAN 2和VLAN 3透传到SwitchB。
<HUAWEI> system-view
[HUAWEI] sysname SwitchB
[SwitchB] vlan batch 2 3 4 10
[SwitchB] interface gigabitethernet 1/0/5
[SwitchB-GigabitEthernet1/0/5] port link-type trunk
[SwitchB-GigabitEthernet1/0/5] port trunk allow-pass vlan 2 3
[SwitchB-GigabitEthernet1/0/5] quit
# 在SwitchB上配置Super-VLAN 4，并将VLAN 2、VLAN 3加入到Super-VLAN 4，作为
其Sub-VLAN。
[SwitchB] vlan 4
[SwitchB-vlan4] aggregate-vlan
[SwitchB-vlan4] access-vlan 2 to 3
[SwitchB-vlan4] quit
# 创建并配置VLANIF4，使不同部门的用户可通过Super-VLAN 4访问Internet。
[SwitchB] interface vlanif 4
[SwitchB-Vlanif4] ip address 10.1.1.1 24
[SwitchB-Vlanif4] quit
# 配置上行接口GE1/0/1，透传SwitchB与出口网关Router的互连VLAN。
[SwitchB] interface gigabitethernet 1/0/1
[SwitchB-GigabitEthernet1/0/1] port link-type trunk
[SwitchB-GigabitEthernet1/0/1] port trunk allow-pass vlan 10
[SwitchB-GigabitEthernet1/0/1] quit
# 创建并配置VLANIF10，指定其IP地址为SwitchB与出口网关Router对接的IP地址。
[SwitchB] interface vlanif 10
[SwitchB-Vlanif10] ip address 10.10.1.1 24
[SwitchB-Vlanif10] quit
# 在SwitchB上配置一条到出口网关Router的缺省静态路由，使用户能够访问Internet。
[SwitchB] ip route-static 0.0.0.0 0.0.0.0 10.10.1.2