配置Eth-Trunk+VRRP 与接口状态联动示例

胡振宇

<HUAWEI> system-view
[HUAWEI] sysname SwitchA
[SwitchA] vlan batch 11 to 15 101 to 180 301 to 305 400
[SwitchA] interface gigabitethernet 1/0/1
[SwitchA-GigabitEthernet1/0/1] port link-type trunk
[SwitchA-GigabitEthernet1/0/1] undo port trunk allow-pass vlan 1
[SwitchA-GigabitEthernet1/0/1] port trunk allow-pass vlan 400
[SwitchA-GigabitEthernet1/0/1] quit
[SwitchA] interface gigabitethernet 1/0/2
[SwitchA-GigabitEthernet1/0/2] port link-type trunk
[SwitchA-GigabitEthernet1/0/2] undo port trunk allow-pass vlan 1
[SwitchA-GigabitEthernet1/0/2] port trunk allow-pass vlan 101 to 180
[SwitchA-GigabitEthernet1/0/2] quit
[SwitchA] interface vlanif 11
[SwitchA-Vlanif11] ip address 10.1.1.2 24
[SwitchA-Vlanif11] quit
[SwitchA] interface vlanif 12
[SwitchA-Vlanif12] ip address 10.1.2.2 24
[SwitchA-Vlanif12] quit
[SwitchA] interface vlanif 13
[SwitchA-Vlanif13] ip address 10.1.3.2 24
[SwitchA-Vlanif13] quit
[SwitchA] interface vlanif 14
[SwitchA-Vlanif14] ip address 10.1.4.2 24
[SwitchA-Vlanif14] quit
[SwitchA] interface vlanif 15
[SwitchA-Vlanif15] ip address 10.1.5.2 24
[SwitchA-Vlanif15] quit
[SwitchA] interface vlanif 400
[SwitchA-Vlanif400] ip address 192.168.1.1 24
[SwitchA-Vlanif400] quit
# 配置汇聚层交换机Switch的二层透传功能。
<HUAWEI> system-view
[HUAWEI] sysname Switch
[Switch] vlan batch 11 to 15 101 to 180
[Switch] interface gigabitethernet 1/0/1
S7700&S9700 系列交换机
典型配置举例3 基础特性典型配置
文档版本 04 (2015-10-23) 华为专有和保密信息
版权所有 &copy; 华为技术有限公司
184
[Switch-GigabitEthernet1/0/1] port link-type trunk
[Switch-GigabitEthernet1/0/1] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet1/0/1] port trunk allow-pass vlan 11 to 15 101 to 180
[Switch-GigabitEthernet1/0/1] quit
[Switch] interface gigabitethernet 1/0/2
[Switch-GigabitEthernet1/0/2] port link-type trunk
[Switch-GigabitEthernet1/0/2] undo port trunk allow-pass vlan 1
[Switch-GigabitEthernet1/0/2] port trunk allow-pass vlan 11 to 15 101 to 180
[Switch-GigabitEthernet1/0/2] quit
# 配置核心层交换机SwitchA、SwitchB和Switch之间采用OSPF协议进行互连。以
SwitchA为例，SwitchB和SwitchC的配置与SwitchA类似，详见配置文件。
[SwitchA] ospf 1
[SwitchA-ospf-1] area 0
[SwitchA-ospf-1-area-0.0.0.0] network 10.1.1.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] network 10.1.2.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] network 10.1.3.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] network 10.1.4.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] network 10.1.5.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] network 192.168.1.0 0.0.0.255
[SwitchA-ospf-1-area-0.0.0.0] quit
[SwitchA-ospf-1] quit
步骤2 在核心层交换机SwitchA和SwitchB上配置super-VLAN
# 配置super-VLAN，以SwitchA为例。SwitchB的配置与SwitchA类似，详见配置文件。
[SwitchA] vlan 11
[SwitchA-vlan11] aggregate-vlan
[SwitchA-vlan11] access-vlan 101 to 116 301
[SwitchA-vlan11] quit
[SwitchA] vlan 12
[SwitchA-vlan12] aggregate-vlan
[SwitchA-vlan12] access-vlan 117 to 132 302
[SwitchA-vlan12] quit
[SwitchA] vlan 13
[SwitchA-vlan13] aggregate-vlan
[SwitchA-vlan13] access-vlan 133 to 148 303
[SwitchA-vlan13] quit
[SwitchA] vlan 14
[SwitchA-vlan14] aggregate-vlan
[SwitchA-vlan14] access-vlan 149 to 164 304
[SwitchA-vlan14] quit
[SwitchA] vlan 15
[SwitchA-vlan15] aggregate-vlan
[SwitchA-vlan15] access-vlan 165 to 180 305
[SwitchA-vlan15] quit
步骤3 在核心层交换机SwitchA和SwitchB上配置链路聚合
# 在SwitchA上创建Eth-Trunk1并配置为LACP模式，SwitchB的配置与SwitchA类似，详
见配置文件。
[SwitchA] interface eth-trunk 1
[SwitchA-Eth-Trunk1] mode lacp
[SwitchA-Eth-Trunk1] port link-type trunk
[SwitchA-Eth-Trunk1] undo port trunk allow-pass vlan 1
[SwitchA-Eth-Trunk1] port trunk allow-pass vlan 301 to 305
[SwitchA-Eth-Trunk1] quit
# 配置SwitchA上的成员接口加入Eth-Trunk，SwitchB的配置与SwitchA类似，详见配置
文件。
[SwitchA] interface gigabitethernet 1/0/3
[SwitchA-GigabitEthernet1/0/3] eth-trunk 1
[SwitchA-GigabitEthernet1/0/3] quit
[SwitchA] interface gigabitethernet 1/0/4
S7700&S9700 系列交换机
典型配置举例3 基础特性典型配置
文档版本 04 (2015-10-23) 华为专有和保密信息