配置堆叠系统对接NLB 服务器群集示例（通过物理链路

胡振宇

<HUAWEI> system-view
[HUAWEI] sysname iStack
[iStack] vlan batch 100 200
[iStack] interface gigabitethernet 0/0/1
[iStack-GigabitEthernet0/0/1] port link-type access
[iStack-GigabitEthernet0/0/1] port default vlan 100
[iStack-GigabitEthernet0/0/1] quit
# 配置接口GE1/0/1加入VLAN100。
[iStack] interface gigabitethernet 1/0/1
[iStack-GigabitEthernet1/0/1] port link-type access
[iStack-GigabitEthernet1/0/1] port default vlan 100
[iStack-GigabitEthernet1/0/1] quit
步骤2 配置接口加入Eth-Trunk
# 配置接口GE0/0/4和GE1/0/4加入Eth-Trunk4。
[iStack] interface eth-trunk 4
[iStack-Eth-Trunk4] quit
[iStack] interface gigabitethernet 0/0/4
[iStack-GigabitEthernet0/0/4] eth-trunk 4
[iStack-GigabitEthernet0/0/4] quit
[iStack] interface gigabitethernet 1/0/4
[iStack-GigabitEthernet1/0/4] eth-trunk 4
[iStack-GigabitEthernet1/0/4] quit
# 配置接口GE0/0/5和GE1/0/5加入Eth-Trunk5。
[iStack] interface eth-trunk 5
[iStack-Eth-Trunk5] quit
[iStack] interface gigabitethernet 0/0/5
[iStack-GigabitEthernet0/0/5] eth-trunk 5
[iStack-GigabitEthernet0/0/5] quit
[iStack] interface gigabitethernet 1/0/5
[iStack-GigabitEthernet1/0/5] eth-trunk 5
[iStack-GigabitEthernet1/0/5] quit
步骤3 配置自环口Eth-Trunk4和Eth-Trunk5
# 去使能接口Eth-Trunk4和Eth-Trunk5的STP/RSTP/VBST/MSTP功能。
[iStack] interface eth-trunk 4
[iStack-Eth-Trunk4] undo stp enable //去使能STP/RSTP/VBST/MSTP功能
[iStack-Eth-Trunk4] quit
[iStack] interface eth-trunk 5
[iStack-Eth-Trunk5] undo stp enable //去使能STP/RSTP/VBST/MSTP功能
[iStack-Eth-Trunk5] quit
# 配置接口Eth-Trunk4和Eth-Trunk5以Access类型分别加入VLAN100和VLAN200。
[iStack] interface eth-trunk 4
[iStack-Eth-Trunk4] port link-type access
[iStack-Eth-Trunk4] port default vlan 100
[iStack-Eth-Trunk4] quit
[iStack] interface eth-trunk 5
[iStack-Eth-Trunk5] port link-type access
[iStack-Eth-Trunk5] port default vlan 200
[iStack-Eth-Trunk5] quit
S7700&S9700 系列交换机
典型配置举例11 交换机与服务器对接配置
文档版本 04 (2015-10-23) 华为专有和保密信息
版权所有 &copy; 华为技术有限公司
1222
步骤4 配置NLB服务器群集网关的IP地址
[iStack] interface vlanif 200
[iStack-Vlanif200] ip address 10.128.246.250 24
[iStack-Vlanif200] quit
步骤5 配置静态ARP表项，静态ARP表项的IP地址为群集IP地址10.128.246.252，MAC地址为
群集组播MAC地址03bf-0a80-f6fc，出接口为VLAN200所在的接口Eth-Trunk5
[iStack] arp static 10.128.246.252 03bf-0a80-f6fc vid 200 interface eth-trunk 5 //配置静态ARP表
项
步骤6 连接接口Switch_1上的GE0/0/4和GE0/0/5、Switch_2上的GE1/0/4和GE1/0/5
上述配置完成后，进行物理连线。
步骤7 检查配置结果
上述配置完成后，发往NLB服务器群集IP地址的报文Server_